Product Information

Gas-Slotted or Cross-Drilled vented OEM factory sized front rotors to provide more cooling surface area and provide pad out gassing. Featuring asymmetrical and directional vent pattern to provide cooler and longer lasting rotors. Virtually eliminating glazing, warpage and stress cracking. Providing better initial bite and superior heat dissipation

Severe Service Blue-Printed Calipers with special phenalic or stainless steel pistons, high temp silicon seals and boots (depending on application), stainless steel or hard coated slider pins, high heat pin lube and required hardware. Double pressure tested and covered by a life time guarantee against manufacture's defects. These blue-printed remanufactured units feature hand fitted pistons, setting the "Hot Running" clearence so that as the piston(s) expand-no sticking or binding occurs. Providing superior performance and heat dissipation based on the piston upgrade and design.

Pads & Shoes
Special Carbon Kevlar integrally molded Disc Pads and Brake Shoes. The latest technology now allows us to provide "State of the Art" Pads and Shoes! Heat cured to remove air pockets from the compressed friction material to eliminate brake noise and provide unsurpassed heat transfer. Utilizing Carbon Kevlar technology, the fiber strands in conjunction with metal particles combine to absorb vibration, a leading cause of brake noise. Allowing faster heat dissipation, a major cause of warped and stress cracked rotors. Quicker heat dissipation means less fade and less pedal pressure, which in turns results in less pad and rotor wear. The dynamic coefficient actually grips better as the temperature goes up. Our Carbon Kevlar pads and shoes provide unequaled stopping distances for heavy loads and high heat applications. And are the ultimate for heavy towing and load requirements. Available for most all vehicles and trailers as well.

DENSITY: 3.0 TO 3.2.
HARDNESS: 81.3 Rockwell.
MATERIAL: Carbon Kevlar Metallic and Ceramic
DYNAMIC COEFFICIENT: Cold application .425 increases to .485 when running at higher temperatures.
CONSTRUCTION: Utilizes ceramic inner layer between the friction material and the backing plate to reduce heat penetration to the brake fluid system.

Complete kit shown

Brake Fluid
Motul RBF 600 Synthetic Brake Fluid, boasts extremely high boiling points: Dry 594 degrees And Wet 421 degrees, with exceptional recovery time, maintaining thermal viscosity. Virtually eliminates vapor lock and brake fade. Motul 600 is fully miscible with synthetic brake fluids complying with SAE J1703, DOT 3,4, and 5.1, Which it can replace with out any special precautionary measures. Mixes and works safely with all ABS systems. Not to be used with mineral based or silicon fluids. Simply the best fluid available for high temperature and high performance braking systems.

Wheel Cylinders
Larger Wheel Cylinders available for some application (i.e. Dodge Ram, Ford & Chevy). These larger wheel cylinders provide more clamping force to the rear axle providing more stopping force and more heat dissipation in to the rear drums reducing the thermal load on the front braking system.

Speed Bleeders and Brake Fluid Catch Bags
Speed Bleeder bleeder screws kits and brake fluid catch bags. Makes bleeding much faster and easier-a one man job! Available for all models of cars and trucks.

Special Bleeders

Kevlar Braided Stainless Steel Brake Hoses for Dodge Ram Pickups

EGR Performance Brakes offers its new Kevlar Braided Stainless Steel Brake Line kits for 1982 thru 2003 Dodge Ram, Chevrolet and Ford, 1/2,3/4 & 1 ton, 2 and 4 wheel drive models. Finally a Solution to soft and spongy stock rubber hoses that expand and stretch each time the pedal is applied, while deteriorating from UV exposure and aging These New Brake hose replacements provide a firmer pedal and less pedal travel, eliminating "hose swell". Featuring "State of the Art Construction utilizing a Kevlar Braided sheath over Teflon tubing, protected with a Stainless Steel outer sleeve. Complete 3 or 4 piece kits with crimped ends and special mounting brackets to fit Dodge pickups. Certified by an independent testing lab, meeting D.O.T. FMVSS-106 and MIL specifications. Each line is Individually pressure tested and approved, these are the only street legal lines for sale and use in the US on Dodge Pickups. Custom built longer hoses also available for Lifted Trucks.

Brake Lines


Click for Ford Truck Brake Parts Excursion Brake Parts Dakota Brake Parts Dodge Ram Brake Parts Dodge Durango Brake Parts Suburban, Tahoe and Yukon Brake Parts Chevy/GMC Brake Parts
Ford F250/F350
Ford Escursion
Dodge Dakota
Dodge Ram
Dodge Durango
Suburban / Tahoe
Chevy / GMC

Home - About Us - Products - Packages - Specials - Tech Info - Photo Gallery - Testimonials - Contact Us - Place Order

Copyright 2016 © EGR PERFORMANCE Inc.  Got Brakes?™ - trademark of EGR PERFORMANCE Inc.
Pages and photos not to be copied or used without permission of EGR PERFORMANCE BRAKES.